After reinstalling Windows 7, how to set up the Internet: the instruction

Today we will talk with you about what to doafter reinstalling Windows 7. How to configure Internet in this operating system? What can we need? How long does the process take? We'll talk about all this today. Let's start, perhaps, with the fact that we will discuss some points on the preparation for the process.

Getting Ready

Well, if you do not know what to do after reinstalling Windows 7, how to set up the Internet so that it starts working normally, then let's deal with this difficult issue.

First of all, we need equipment foraccess to the World Wide Web. Now it can be anything from a USB modem to the most common ADSL modem. For each device there is a customization method. We will analyze them today.

In addition, if you think what to do afterreinstalling Windows 7, how to configure the Internet so that it works fine, then you'll have to stock up on time and patience. Quite often in the operating system there may be failures and malfunctions that interfere with normal operation and slow down the processes of setting up the equipment. So let's try to start with you now.

System Preparation

You do not know how to connect the Internet afterreinstall Windows 7? It is not only necessary to prepare yourself, but also correctly prepare the operating system. This will help reduce the risk of failures and malfunctions to a minimum. Especially after a "clean" installation on the computer.

What is needed for this? Install drivers for all connected equipment. Except for the modem, of course. We'll work with him a little later. Instead, take all the drives with the drivers that you have (network card, video card, sound card, etc.) and install them one by one on the computer. After carrying out this procedure, do not forget to reboot.

Now we can think what to do afterreinstalling Windows 7. How to configure the Internet? It is quite easy to do this if you know where to start. Let's try with you to deal with more "ancient" equipment, and then we'll start to innovate.

ADSL modem

So, we proceed with you to the mostwidespread connection to the World Wide Web. In addition, the method considered now is considered the oldest. It implies connection via ADSL modem.

Do not know how it goes after reinstallingWindows 7 Internet setup? We will first have to connect the equipment to the computer. To do this, plug all the wires into the corresponding sockets on the "box", and one end of the "main" wire should be shoved into the computer. It is connected to a special socket on the network card (it is impossible to confuse). After that you can turn on the computer and start working.

We will need to install drivers forequipment. This is done using an installation disc, which, as a rule, goes in a set with the equipment. Are you ready? Then go to the "Control Panel", and then - to "Network and the Internet." There, find the "Network and Sharing Center", and then select the "Create a new connection" window at the bottom.

If you do not have the Internet after reinstallationWindows 7, then you can continue our actions. In the window that appears, select "Connect to the workplace" and then "No, create a connection". Use "My connection to the Internet VPN". Then click on "Delay the Internet setting", enter the IP address in the "Internet address". Call it connection somehow, come up with a password and save it.

Return to the "Network Management Center". You will see that a new connection has appeared. Click on it with the right mouse button and select "Properties". We will work in the "Security" tab. Connection type select "Tunnel protocol", and as data encryption - "Connect even without encryption".

Think about how to connect to the Internet afterreinstall Windows 7? Go to the "Network" tab. Check "Internet Protocol version 6 (TCP / IPv6)" and save. Again, go to "Connection Properties". Now in the "Network" section click on the properties of "Internet Protocol version 4" and enter the ip-address and subnet mask in the window that appeared (you should tell them the provider). Leave the remaining fields empty. Save the changes. That's all.

USB

Do you still think what to do after reinstallingWindows 7, how to configure the Internet to work properly with a computer using a USB modem? As a rule, you do not need practically any action.

You should start with modem connection (with advanceinserted into it by a SIM card) to your "machine". It is best to attach the equipment to the socket where it will be more convenient to get it. After that, you will need to install drivers and a special program for working with the modem. To do this, you can either use the supplied disk, or wait a little - installation usually takes place automatically after attaching the equipment.

After the process is completed, we will be able toenter the program manager, enter your login and password (phone number and password given to you), and then safely use the Internet connection. As you can see, nothing complicated.

USB Router

And here is another interesting method that allows you to use the Internet. This is using a USB router. With it, problems, as a rule, arise a little less than with portable modems.

To begin, insert the SIM card in the equipment andbattery. Charge the "machine" with a special charger, and then connect it with a wire to the USB-connector. Turn on the equipment and install the necessary drivers on it. They are supplied complete with a "sim card" and a router.

Now you will need to wait for the installationa special manager to enter the network. After the process is completed, you can safely use the Internet. It will be enough to dial in the login and password, after including the router itself. That's all the case. As you can see, nothing complicated or special.

Wi-Fi

If you notice that you do not have the Internetafter reinstalling Windows 7, but there is a computer connected to the World Wide Web with Wi-Fi equipment, do not worry: you can quickly regain access.

This will require the presence of Wi-Fi networkmap. If this option is not available, then you can buy a special antenna for this venture. Install the drivers for the hardware, and then click on the small scale in the tray. There select your network and click "connect". If necessary, enter the password several times. After a while you will see how the scale began to fill up, and the computer will report a successful connection. You can use the Internet.